|
Heavy-Duty Bag for 18 inch
Stakes or Rebar |
 |
Heavy-Duty Bag with Center
Partition |
|
8090-20-ORG |
8091-20-ORG |
|
The main compartment of this
bag is constructed of tough Rhinotek
material and designed to hold 18 inch stakes or rebar. Other features
include a hammer loop, an adjustable strap and brass grommet drain holes at
both ends of the bag. |
This is the same bag as the
8090-20-ORG but it features a partition down the middle of the bag for
separating stakes and hubs. |
| |
|
|
|
Heavy-Duty Bag for 24 inch
Stakes or Rebar |
 |
Heavy-Duty Bag with Center
Partition |
|
8092-20-ORG |
8096-20 (Shown) |
|
This is the same bag as the
8090-20-ORG, made for 24
inch stakes and rebar.
|
This is the same bag as the 8092-20-ORG but it features a partition down the
middle of the bag for separating stakes and hubs. |
| |
|
|
|
Lath Bag |
Heavy-Duty Bag for Stakes
or Rebar |
Wire Stake Flag Bags |
8100-00-ORG - For 36 inch
Lath (Shown)
8101-00-ORG - For 48
inch Lath
|
8100-20-ORG (For 36 inch)
8101-20-ORG (For 48
inch)
|
8093-00-ORG (For 21 inch
flags)
8094-00-ORG (For 30
inch flags)
|
|
8 inch diameter bag holds 36
or 48 inch wood lath. It has a hand loop, shoulder strap, and an
outside pocket.
Weighs 0.22 lb (0.10 kg) and
0.28 lbs (0.13 kg) respectively
|
Rhinotek
lining on bottom of bag and 6 inches up the sides. |
Weighs 0.22 lbs (0.10 kg) and
0.28 lbs (0.13 kg) respectively |
|
|
 |
|
| |
|
|
|
Surveyor's Tool Pouch with
Belt |
Lath Carrier |
Heavy-Duty Lath Carrier |
| 8046-30-ORG |
8102-00-ORG |
8102-01-ORG |
| The Surveyor's Tool Pouch
features a 9 x 2 x 11 inch pocket with two vent grommets. The large
pocket is lined with tow layers of 1000D Corduraฎ.
A smaller pocket on the front is made of durable Rhinotek.
Other features include a hammer loop and marker storage. The webbed
belt adjusts to a 50 inch waist. |
his carrier measures 33
inches (84 cm) long with two handles straps. Carries up to 50 lath.
Weighs 1.46 lbs (0.66 kg)
|
This SECO carrier can hold up to 50 lath. It can handle rebar too! This
1000 denier Cordura bag has a thick, reinforced bottom of leather and the
advanced Rhinotek abrasive-resistant material. The exterior features a
hammer loop, paint can holder, marker pen slots, and a pocket for
miscellaneous gear.
Weighs 0.22 lb (0.10 kg)
|
 |
|
|
| |
|
|
|
Lath Bag |
Bag for 18 inch Wood
Stakes |
Bag for 24 inch Wood
Stakes |
|
8103-00-ORG
8103-20-ORG (with Rhinotek) |
8090-00-ORG
8091-00-ORG |
8092-00-ORG
8096-00-ORG |
|
8 inch diameter bag holds 24
inch (61 cm) wood lath. It has a hand loop, shoulder strap, and an
outside pocket.
Weighs 0.4 lb (0.18 kg)
|
For 18 inch stakes and rebar.
The 8091-00-ORG has a center partition to separate stakes and hubs. Measures: 19 x 8 x 12 inches
Weighs 0.78 lb (0.35 kg)
|
For 24 inch (61 cm) stakes
and rebar. The 8096-00-ORG has a center partition to separate stakes
and hubs. Measures 25 x 8 x 12 inches (63.5 x 20.3 x 30.5 cm).
Weighs 0.95 lbs (0.50 kg)
|
|
|
 |
 |
|
|
|
|
|
Heavy-Duty Lath Carrier |
Collapsible Bucket |
Heavy-Duty Bucket Bag |
|
8104-20-ORG |
8095-00-ORG
8097-20-ORG (With back
pocket) |
8095-50-RED |
| This heavy-duty lath carrier
features space inside for any standard 12 inch, five gallon. Weighs
1.5 lb (0.68 kg) without bucket and approximately 3.85 lb (1.75 kg) with
bucket added. |
Features include an outside
pocket, a hand axe loop, and a leather reinforced bottom. Measures 10
x 15 inches (25 x 38 cm). Weighs 1.3 lb (0.59 kg). |
This heavy-duty,
water-resistant bucket bag is reinforced at all the wear points. It
features plenty of pockets.
Weighs 1.6 lb (0.73 kg)
|
|
 |
 |
 |
| |
|
|
Flagging Dispenser |
Spray Can Holder |
8025-00-ORG
|
8098-00-ORG (Standard
Holder)
8098-10-ORG (With
accessory pockets)
|
|
Holds four rolls of flagging! The belt strap can be used around the
waist or over the shoulder. |
Choose between a standard
spray can holder or a holder with updated features like four pockets for
pens/pencils and a heavy web strap. |
 |
 |
