|
| |
| |
|
 |
GPS
ACCESSORIES |
|
Heavy-Duty GPS Antenna
Tripods |
|
5119-10-FLY
Standard
Model-Fluorescent Yellow or Yellow |
5119-11-FLY
With Precise Adjusters-
Fluorescent Yellow or Yellow |
5119-12-FLY
With Precise Adjusters
and Dual Points-Fluorescent Yellow or Yellow |
|
This
tripod is heavy-duty, with a round 6 inch diameter head which easily holds
lasers or robots. Its larger telescoping legs (1.25 - to 1.50- inch
diameters) feature adjustable handle bolts on the leg pivots creating
greater stability. No tools are needed to set the leg pivot tension!
The #5119-11-FLY has the same
features as the #5119-10-FLY but includes precise adjusters to make
centering the 8-minute vial easier. The adjusters provide fine leg
extension, a range of ± 0.25- inch from the center line. It's like
having leveling screws for a tripod!
The #5119-12-FLY is identical
to the #5119-11-FLY with the addition of double leg points. Dual
points create more bite in the ground to minimize the chance for twisting.
Double points are useful with angle measuring instruments such as robots.
All three models are suitable
for GPS and machine-control applications.
Each weigh approximately 20
lbs (9.07 kg). |
 |
|
 Precise
Leg adjusters
|
 Large 6 inch
diameter head |
 Double
Leg Points |
|
GPS Tie-Down Kit |
5119-010-ORG |
This kit
consists of three SECO Tie Rods with twist clamps on the ends and a kit bag
which will hold three SECO Tie Rods, three metal stakes up to 30 inches in
length and a hammer (stakes and hammer not included). This kit will
help secure a tripod in windy conditions! Weighs 4.7 lbs (2.13 kg). |
 |
| |
|
Heavy-Duty GPS Tripod
Bag |
8154-12-ORG |
Make sure you
heavy-duty SECO GPS Tripod is protected in this extra-tough Tripod Bag.
This bag features heavy-duty Cordura®
material and Rhinotek® end pieces for superior strength and longevity.
It includes a shoulder strap. Measures: 8 inches I.D. x 56 inches.
Weighs 1.8 lbs. |
 |
|
Heavy-Duty GPS Antenna Tripod |
5115-10-FLY Fluorescent Yellow
(Shown) |
This
tripod is the heavy-duty version of SECO's original 2-meter GPS Tripod.
The fixed height center pole measures 2 meters and rotates 360°
for checking. It comes with an 8-minute circular vial. A compass
is included as part of the handle set. The large telescoping legs have
a 1.25-to-1.50-inch-diameter and extend to 3.2 meters (10.5 feet); its large
round head measures 6-inches in diameter and features a removable brass 5/8
x 11 stud. This tripod is is suitable for machine control instruments,
scanners, lasers, robots, prism backsights; anything that needs to be
plumbed over a point. Weighs 24.2 lb (11 kg). |
 |
|
5115-10-YEL Yellow |
|
5115-11-FLY (With Precise Adjusters) Fluorescent Yellow
|
|
5115-11-YEL
(With Precise Adjusters) Yellow
|
| |
|
|
|
|
Standard Fixed-Height GPS Antenna Tripod |
5115-00-FLY Fluorescent Yellow |
This
tripod has a fixed-height, two meter off center staff that rotates 360°
for calibrating the 8-minute vial. It also features a removable 5/8 x
11 adapter, and an on-board compass. The extendable tripod legs and
the pole are electrstatically powder painted and include replaceable points.
The aluminum hardware is anodized black. Weighs 15 lbs (6.8 kg).
Don't forget a tripod bag! See below. |
THE ORIGINAL!
 |
|
5115-00-YEL Yellow |
| |
|
|
|
|
GPS Antenna
Tripod Bag |
8153-00-ORG |
This bag features a
full-length zipper and shoulder strap. Perfect for the Standard
Fixed-Height GPS Antenna Tripod (5115-00-FLY or 5115-00-YEL) listed above. Measures 7 x 78 inches.
Also available in green. |
 |
| |
|
|
|
|
Graduated
Collapsible GPS Antenna Tripod |
5119-00-FLY Fluorescent Yellow |
This
tripod features a collapsible center staff with twist-locking mechanism that
rotates 360° for calibrating the 8-minute vial.
It also features quick release and twist-locking mechanisms on the legs.
It is dual graduatated and adjusts to three heights: 2 m, 1.8 m and 1.5 m.
It collapses to 50 inches (127 cm). Other features include a removable
5/8 x 11 adapter, and an on-board compass. The extendable tripod legs
and the pole are electrostatically powder painted and includes replaceable
points. The aluminum hardware is anodized black. Weighs 15 lbs
(6.8 kg). Don't forget a tripod bag! See below. |
THE ORIGINAL!
|
|
5119-00-YEL Yellow |
| |
|
|
|
|
GPS Antenna
Tripod Bag |
8154-00-XXX |
This is the perfect bag for the Graduated
Collapsible GPS Antenna Tripod (#5119-00-FLY or 5119-00-YEL). The bag features a
full-length zipper and shoulder strap. Measures 7 x 50 inches. Available in orange and
green. |
 |
|
Ajustable-Tilt, Stainless
Steel Monument Adapters |
2072-30
For use with 1.5 inch pipe with MPT
1-1/2 x 11-1/2 TPI |
These Adjustable-Tilt Monument Adapters
are the professional solution to fit between your GPS antenna and the mast
of your network monument. The 2072 Series adapters have 3.20 inch
(8.19 cm) diameters and an overall height of 3.036 inches (7.71 cm).
Each adapter include a removable brass 5/8 x 11 male stud that is adjustable
in azimuth and held in location by two set screws. The adapters are
leveled by three adjusting screws with a tilt range of +/-7 degrees.
The height above the pivot point to the stud is 1.37 inches (3.50 cm).
The height below the brass is 5/8 stud to the shoulder is 0.463 inches (1.18
cm). The axis height is engraved on the outside of the monuments. |
 |
|
2072-30
For use with 2 inch pipe with MPT
2 x 11-1/2 TPI |
|
2072-31
For use with 3 inch pipe with MPT
3-1/2 x 8 TPI |
|
2072-33
For use with male
5/8 x 11 TPI |
| |
|
|
|
|
Masonry Mount Adapter |
2072-20 |
Use this adapter for antenna mounts.
It's easy to install, drill three 5/8 x 11 holes and fill with epoxy.
The brass rotating adapter is removable and locks in the azimuth direction.
The body is made of anodized aluminum with stainless steel 3/8 x 2-1/2 inch
bolts. Weighs 1.4 lbs (0.61 kg). |
 |
| |
|
|
|
|
Antenna Mast Adapter |
2072-10 |
Use the adapter for network GPS antenna
mounts. It's easy to install it, it attaches to standard 2 inch
threaded pipe used as the 'mast'. The brass rotating adapter is
removable and locks in the azimuth direction. The body is made of
anodized aluminum. Weighs 2.0 lbs (0.91 kg). |
 |
|
All-Terrain Rover Rod
20-inch 'Big Wheel' |
5125-056- without rod
5125-057-FLY - with aluminum rod
5128-052 - with carbon fiber rod |
The Big Wheel is ideal for RTK profiling.
Weighs 3.8 lbs (1.72 kg). |
 |
| |
|
|
|
|
Snap-Lock Rover
Rods |
5125-20-FLY Aluminum Model (Shown) |
These rover rods are faster to setup and more user friendly compared to
traditional two-piece, screw-together rods. They feature a one-piece
design and two locking systems for stability, the snap lock prevents
slippage and the compression lock centers the telescopic inner poles and
maintains straightness. The lightweight rods come with 40-minute
vials. The
aluminum model telescopes and locks at 2 meters and collapses to 1.354
meters. The GT model features a 10ths/100ths graduated outer pole.
Call us for color options. A GM (metric) models is also
available. Weighs 2.3 lb (1.5 kg).
The
carbon fiber model telescopes and locks at 2 meters and collapses to 1.354
meters. Carbon fiber is strong, dent resistant and has a 'zero'
coefficient of expansion. A GT model is also avaiable. Weighs
1.60 lb (0.72 kg).
|
 |
|
5128-20 - GM (Carbon Fiber - Shown) |
|
5128-21 - Quick Release Tip (Carbon
Fiber) |
|
5128-22 - 3 Position (Carbon Fiber) |
| |
|
|
|
|
Heavy-Duty
Snap-Lock Pole System Bag |
8151-02-FLY |
This
bag holds a 2-meter Snap-Lock pole and bipod or tripod connected. It's
constructed of tough Cordura® material
and Rhinotek® ends. Features include a full-length #10 zipper; dual
hand-carry straps, full-length carry straps; full-length shoulder strap; and
a side pocket. Measures 5.5 inches I.D. x 56 inches. Weighs 1.5
lbs (0.68 kg).
 |
| |
|
|
|
|
Telescoping GPS
Carbon Fiber Rover Rods with Locking Pin |
5129-50 - Dual Graduations |
These are designed so the GPS surveyor has all the features needed in a
single rod! They're ideal for kinematic surveys and have a zero height
(0 H.T.), generic for all users. Carbon fiber makes these 30% lighter.
The included pin can set the length of the rod. TLV™ locks with a
40-minute vials are standard. The
5129-50 and 5129-51 lock at 1.8 m, 2 m and 2.2 m. The rods extend 2.4
m (8.14 ft) and collapse to 1.366 m (4.48 ft). Weighs 2.3 lbs.
The 5129-70and 5129-71 lock at every
20 cm mark starting at 1.8 m. The rods
extend to 3.57 m (11.70 ft) and collapse to 1.43 m (4.69 ft). Weighs
3.3 lb (1.5 kg). |
 |
|
5129-51 Centimeter Graduations |
|
5129-70 - Dual Graduations |
|
5129-71 - Centimeter Graduations |
| |
|
|
|
|
GPS Rover Rod Hard Shell
Case |
8162-20-BLK |
Store your SECO two-piece rover rod in
this hard shell case and know it's protected. Measures 4 inches in
diameter x 41 inches tall (10.16 cm in diameter x 104.14 cm high).
Weighs 3.2 lbs 91.4 kg).
 |
| |
|
|
|
Two Piece Rover
Rods |
5128-00
Carbon Fiber |
This
featherweight Carbon Fiber Road is ideal for GPS applications. The rover rod is a fixed
height of 2 meters. Includes a 40-minute vial and a male 5/8 x 11 tip.
Weighs 1.42 lbs (0.64 kg).
 |
|
5125-00-YEL
Aluminum |
The aluminum rod features a
40-minute vial, 5/8 x 11 tip, vinyl hand grip, and replaceable steel point.
This model is also available with a quick-release adapter tip option,
#5125-01-YEL. The quick release adapter stays fixed to the GPS
antenna. The quick release pin prevents the antenna from rotating.
Weighs 3 lb (1.36 kg).
|
| |
|
|
|
|
3 Position Carbon Fiber
Snap-Lock Rover Rod |
5128-22 |
SECO's new 3-Position Carbon Fiber Rover
Rod features a one-piece design that is faster and more user friendly.
Ideal for GPS RTK surveys, the rod telescopes and locks at 3 different
heights of 2 m, 1.8 m and 1.6 m. It collapses to 1.343 m. The
rod has two locking systems: the no-slip snap-lock and a compression lock
that centers the telescoping inner and maintains straightness.
Includes a 40-minute, adjustable circular vial. Dent-resistant carbon
fiber is strong and has a zero coefficient of expansion. It weighs
1.75 lbs (0.79 kg). |
 |
| |
|
|
|
|
Two Meter Height Pin |
7751-50 |
The height pin is ideal for measuring
antenna heights because of its 1-mm accuracy. It has dual grads in
100ths and millimeters. The Height Pin is 6.6 feet (201 cm) long and
only 16.5 inches (43 cm) when collapsed. Weighs 0.3 lbs (0.14 kg). |
 |
| |
|
|
|
|
Satellite Stick
Collapsible 2-Meter GIS Pole |
5126-00 |
The Satellite Stick
™ is composed of six 15 mm OD
carbon fiber sections connected by an elastic shock cord.
Collapses to 1.18 feet (36.1 cm). Weighs 1 lb (0.45 kg). |
 |
| |
|
|
|
|
Satellite Stick XL-
Sectional 2-Meter GPS/GIS Pole |
5126-10 |
The Satellite Stick™ XL is composed of
six, one inch OD carbon fiber sections connected by an elastic shock cord.
Collapses to 1.23 feet (37.5cm). Weighs 2.4 lbs (1.09 kg). |
 |
| |
|
|
|
|
6 Foot Snap-Lock Hard
Shell Case |
5139-02-FLY - Fluorescent Yellow |
The snap locks into a fixed length of 6
feet. It collapses to 41.5 inches. A 3.5 inch OD adapter
(5182-002) is included for attaching to 5/8 x 11 tripod heads. Weighs
1.4 lbs (0.62 kg).
 |
|
5139-02-YEL - Yellow |
|
GPS Adapters |
|
GPS Quick Disconnect
Adapters |
GPS Quick Release Tip |
GPS Quick Disconnect
Adapter (Stainless Steel) |
GPS Quick Release Adapters |
GPS Quick Release Adapter
(Stainless Steel) |
|
5111-00 (Shown)
5111-01 (not shown)
|
5113-012
|
511-00-SS
|
5187-00 |
5187-00-SS
|
|
The 5111-01 adds 76.2 mm to
rod length. The 5111-01 adds 35 mm to rod length. Use with
#5187-00. Weighs.14 lb (0.06 kg) |
This adapter has male thread
5/8 x 11 threads. Weighs 0.08 lb (0.04 kg) |
Same as #5111-00 but made of
stainless steel!
|
This 5/8 x 11 adds 23.8 mm to
length of rod. Weighs 0.6 lb (0.03 kg). |
Same as #5187-00 but made of
stainless steel! |
 |
 |
 |
 |
 |
|
Quick
Release Adapter for Rover Rods |
5111-03 |
This rover rod adapter is used to make
your 2 meter rod quicker to assemble and release. The clamp screw can
easily be loosened and the two sections separated. The adapter adds 60
mm to the length of the rod. Weighs 0.45 lb (0.20 lbs). |
 |
|
Triple Mag Mount |
Single Mag Mount |
|
5114-01 |
5114-02 (w/ 5/8 inch tip) |
5114-050 |
5114-051 |
|
|
 |
|
 |
This
lightweight magnetic mount systems adapts easier to curved surfaces.
The quick-release adapter allows for quick setups. Weighs 3.4 lb (1.54
kg).
|
Both
magnets have 3.5-inch diameters and weigh approximately 0.92 lbs (0.42 kg).
|
|
Switchable Kelly Magnet |
5114-052 |
Designed to hold onto pipes, flip the
switch to release its hold on metal surfaces. Weighs 0.92 lb (0.42
kg). |
 |
| |
|
|
|
|
HI 2-Meter GPS Pocket
Rod/Tape |
7752-00 |
This removable, free-standing tape
measures GPS antenna height or is used as a pocket tape. The is a dual
grad- ft/10ths/100ths and cm/mm. Weighs 0.25 lb (0.11 kg). |
 |
| |
|
|
|
|
Pole Bracket Kit for
Pathfinder ProXRT |
5198-100 |
Securely hold your Trimble® GPS
Pathfinder® ProXRT receiver securely to any standard rover rod with this
pole bracket kit. It's easy to attach and easy to adjust the height on
the rover rod. It is predrilled for an extra clip and Includes two
pole clamps, one clip and two screws. The machined anodized aluminum
pole clamps have stainless steel screws and will fit rover rods with 3/4
inch (1.90 cm) to 1- 1/4 inch (3.17 cm) diameters. Weighs 0.4 lbs
(0.18 kg). |
 |
| |
|
|
|
|
Radio Antenna Bracket for
Tripod |
2133-05 |
Securely hold a radio antenna to your
survey tripod with this heavy-duty bracket. It fits all full-sized and
heavy-duty tripods and used a 1/2 inch long, 5/8 x 11 male stud to secure
the antenna or extension. You can use it with the SECO Six-Foot Snap
Lock Radio Antenna Pole (#5139-02-XXX) or any extension with a male/female
5/8 x 11 connection. Weighs 1.55 lb (0.70 kg). Pole not
included. |
 |
| |
|
|
|
|
Radio Antenna Mast
Assembly |
5561-20 |
The SECO Antenna Mast Assemlby will fit
most heavy-duty tripods after the bolt assembly has been removed. The
mast telescopes to 7.5 feet (2.3 m) plus use your tripod for added height.
Includes the proper hex too to easily install, so convert your extra tripod
to a radio based set up! Weighs 2.5 lbs (1.13 kg). |
 |
| |
|
|
|
|
Antenna Bracket |
2133-03 |
The open clamp attachment allows quick
and easy connection to the pole. Will connect the 19 and 32 mm
diameter poles. the brass male 5/8 x 11 stud is easily removed for
direct attachment of the radio antenna to the bar. The bracket comes
with a no-slip Vecro® cable strap (#8124-012) to help manage the radio
cable. Weighs 0.22 lbs (0.10 kg). It can be used with a SECO
Radio Antenna Adapter (#2133-00 which adapts 1 1/8 x 18 radio antennas to
any 5/8 x 11 threaded tip. |
 |
| |
|
|
|
|
Antenna Mast Bracket |
2133-10 |
This bracket allows assembly of sections
of standard diameter poles to obtain the desired height above ground of a
GPS or radio antenna. It works with any standard 5/8 x 11 tripod and
any pole sections 1 to 1.25 inch (25 to 32 mm) OD Easy and controlled setups
are achieved by lifting one section at a time up and through the bracket.
6 to 7 meters height is stable when using 1.25 inch sections. For
windy conditions or higher setups a plate for attaching guy wires can be
used. Weighs 0.95 lbs (0.42 kg). |
 |
| |
|
|
|
|
Radio Antenna Tripod with
Antenna Mast |
5300-11
Hardwood/Fiberglass |
Get your radio antenna mast to the
desired height by using this tripod. The mast telescopes to 7.5 ft
(2.3 m) and the tripod can be set to 5.5 feet (1.7 m) for a total elevation
of 13 feet (4 m). the mast is aluminum with a male 5/8 x 11 tip.
The tripod is the SECO #5302-10-ORG. The antenna mast can be purchased
seperately to convert your own heavy-duty tripod as well (order #5561-20).
Weighs 19 lbs (8.62 kg). Includes carry bag item #8154-10. |
 |
|
5300-12 Aluminum |
|
GPS Antenna Platform |
|
2072-40 |
 |
For the most stable setup, use SECO's new
GPS Antenna Platform along with standard cinder blocks (not included) to
create a stable platform. Ideal for reference station installers who
want to evaluate a site for multipath before committing to the
installations. Also, use the platform for private network sites where
the building owner does not want any permanent attachment tot their
building. Use for temporary sites such as networks, construction
sites, AG sites, etc. The mast is 36 inches (91.44 cm) long with
standard 2-inch pipe threads. Sections can be added for more height.
The platform folds up for portability. A removable 5/8 x 11 adapter is
included as well as system carrying bag and system tools. Platform
sections hold 8 x 16 inch (20.32 x 40.64 cm) cinder blocks. The
platform weighs 25 lbs without blocks. |
|
RUXWORKS PT-100 Truck Bed
Transporter |
|
5114-30-01 |
5114-30-02 |
5114-30-03 |
5114-30-04 |
|
GMC/Chevy for model years 1973- 1999 |
Ford F-150 for model years 1992-1996 |
Dodge Ram for model years 2002 - 2008 |
Toyota Tacoma for model years 1995 - 2004 |
|
Ford F-250 for model years 1992 - 2008 |
|
GMC/Chevy 1999 - 2007 |
Toyota Tundra for model years 2000 - 2006 |
|
GMT 800 |
| |
|
|
The RUXWORKS Truck Bed Transporter™ is
for GPS rod transportation for pick-ups in the field that provides a stable,
safe ride. The easy-to-install bracket permanently mounts to the side
of truck and the detachable rod holder with clamp comes off easily for
storage when not in use. A spring-loaded rod clamp has non-marring
rubber jaws to clamp securely. The rod clamp adjusts for all popular
pole sizes. The bottom point receiver is also compatible with 2.5 inch
and 1.25 inch topo shoes. Weighs approximately 22.5 lbs (10.3 kg). |
 |
|
RUXWORKS PT-150 UTV Roll
Cage Transporter |
|
5114-40 |
 |
The RUXWORKS GPS Rod Transporter
™ fits on popular UTVs, by mounting
to either side and takes less than 10 minutes to install. The UTV
bracket has up to 30° of tilt to set your rover rod plumb. The rod
clamp fits all popular rover rods and poles with points and/or topo shoes up
to a 2-1/2 inch 6.35 cm) diameter and has a secure, non-marring quick
release design. The UTV bracket can stay permanently attached to the
UTV. The pole clamp section is 63 inches (160.02) long and
disassembles quickly from the UTV bracket with two quick release pins or two
bolts. Weighs 15 lbs (6.80 kg). |
|
RUXWORKS PT-300 Receiver
Hitch Transporter |
|
5114-50 |
|
The RUXWORKS Transporter
™ fits a standard 2 inch receiver
hitch that is found on most trucks and SUVs. Installs easily in 5
minutes without drilling or modification to the vehicle. The Receiver
Hitch Transporter can be attached on the either the left or right side of
the vehilce. It has an adjustable horizontal bar to fit most vehicle
widths and a bumper clamp that secures the bar to the vehicle to eliminate
movement. The rod clamp fits all popular rover rods and poles with
points and/or topo shoes up to a 2 - 1/2 (6.35 cm) diameter and has a
secure, non-marring quick release design. The rod clamp section is 63
inches long (160.02 cm) and quickly disassembles from the bracket with two
quick release pins or two bolts. Manufactured from strong, welded
steel that is powder-coated to prevent rust. Weighs 28 lbs (12.70 kg). |
 |
|
RUXWORKS PT-250 ATV Rack
Transporter |
|
5114-60 |
 |
The RUXWORKS ATV Transporter™
has an adjustable clamp on the brackets
that fit fits all popular ATVs with tubular luggage racks up to 1 inch
diameter and Polaris® flat luggage racks. The ATV bracket has plus and
minus 5° of tilt adjustment to set your rover rod plumb. The rod clamp
fits all popular rover rods and poles with points and/or topo shoes up to a
2 - 1/2 (6.35 cm) diameter and has a secure, non-marring quick release
design. The ATV bracket can stay permanently attached to the ATV. The
gar is a 42 inch long horizontal bar. he rod clamp section is 63
inches long (160.02 cm) and quickly disassembles from the bracket with two
quick release pins or two bolts.
Manufactured from strong, welded steel that is powder-coated to prevent
rust. Weighs 25 lbs (11.34 kg). |
|
GPS Truck Bracket |
|
 |
5114-20-FLY |
This
system holds a GPS or RTK-type rod to the door of your survey truck.
It's easy to set up and fits most of mid- to full-size pickups and SUVs.
Open and close the doors, roll the windows up and down, all normal door
functions are preserved!
Expands vertically to 61
inches and collapses to 47 inches to fit most trucks or SUVs! |
|
3-inch
Extension Kit |
 |
|
5114-20-051 |
| This kit extends SECO's
#5114-2-FLY GPS Door Bracket to fit on larger-sized trucks! |
|
Topo Shoe Adapter |
 |
|
5114-20-050 |
| This adapter bolts on and
allows rods with topo shoes to be held securely. The adpater holds
2.5- inch and 1.25-inch topo shoes. It will hold rods with regular
points as well. |
| |
|
|
|
Interior
Controller/Collector Bracket System |
|
This bracket series is designed to hold
your data collector or controller insdie the cab of the vehicle that you use
to survey. Use it with the #511-20-FLY above and you can watch the GPS
data from the comfort of your cab. Use the suction cup mount to attach
to any clean glass or slick surface. Includes a two hole base mount
for permanent mounting.
5199-70 Shown. |
Number: |
Designed
for: |
|
5199-60 (Claw) |
TSC2™ , Ranger™ ,
300X, 500X |
|
5199-62 (Claw) |
Allegro, Allegro MX, Jett®, ·ce, FC-2200 |
|
5199-63 (Claw) |
Recon® |
|
5199-64 (Claw) |
FC-100 |
|
5199-65 (Claw) |
FC-1000, FC-2000 |
|
5199-66 (Claw) |
GMS-2, GMS-2 Pro |
|
5199-67(Claw) |
Archer, Leice DX10, Carlson Mini, Javad
Victor |
|
5199-68 (Claw) |
FC-200, FC-120 |
|
5199-69 (Claw) |
Geo XT™ (with cradle #53500-00) |
|
5199-70 (Claw) |
Nomad® 800 Series |
|
5199-71 (Claw) |
GeoCE™ , XT™ , XM™ , XH™ , Geo 2008 |
|
5199-72 (Claw) |
Workabout Pro |
|
5199-73 (Claw) |
Carlson Surveyor, Surveyor + |
|
5199-74 (Claw) |
FC-2500 |
|
The Claw™ |
|
This new and improved clamping system
from SECO features anodized aluminum clamps. These innovative devices
keeps your expensive data collecting hardware securely on the pole without
crushing it. |
|
Quick-Release Cradle |
|
 |
|
Part# |
Designed for: |
|
5200-050 (shown) |
TSC2™,
Ranger™, 300x, 500X |
|
5200-052 |
Allegro, Jett®, ·ce, Explorer, Tracker,
FC-2200 |
|
5200-053 |
Recon® |
|
5200-054 |
FC-100, Mobile Mapper CE, CX |
|
5200-056 |
GMS-2, GMS-2 Pro |
|
5200-057 |
Archer, Leica DX10 |
|
5200-058 |
FC-120, QR, FC-200 |
|
5200-060 |
GeoCE™, XH™,
XT™, XM™ |
|
5200-061 |
Workabout Pro |
|
5200-062 |
Carlson Surveyor, Surveyor+ |
|
5200-063 |
FC-2500 |
|
Quick-Release Clamp |
 |
|
Part# |
Features: |
|
5200-150 |
Plain |
|
5200-151 |
With 40-min vial |
|
5200-152 |
With 20-min vial |
|
5200-154 |
With compass |
|
5200-155 (shown) |
With 40-min vial and compass |
|
Ball-and-Socket Combo |
 |
|
Number: |
Designed for: |
|
5200-00 |
TSC2™,
Ranger™, 300x, 500X |
|
5200-02 |
Allegro, Jett®, ·ce,, FC-2200 |
|
5200-03 |
Recon® |
|
5200-04 |
FC-1000, FC-2000 |
|
5200-05 |
FC-1000, FC-2000 |
|
5200-06 |
GMS-2 |
|
5200-07 |
Archer, Leica DX10, Carslon Mini, Javad
Victor |
|
5200-08 |
FC-120, QR, FC-200 |
|
5200-09 |
Nomad™. 800
Series |
|
5200-10 |
GeoCE™, XH™,
XT™, XM™ |
|
5200-11 |
Workabout Pro |
|
5200-12 |
Carlson Surveyor, Surveyor+ |
|
5200-13 |
FC-2500 |
|
Ball-and-Socket Cradle
(with a 1-inch ram ball) |
 |
|
Part# |
Designed for: |
|
5200-00-050 (shown) |
TSC2™,
Ranger™, 300x, 500X |
|
5200-02-050 |
Allegro, Jett®, ·ce, Explorer, Tracker,
FC-2200 |
|
5200-03-050 |
Recon® |
|
5200-04-050 |
FC-100, Mobile Mapper CE, CX |
|
5200-06-050 |
GMS-2, GMS-2 Pro |
|
5200-07-050 |
Archer, Leica DX10, Carlson MIni,
Javad Victor |
|
5200-08-050 |
FC-120, QR, RC 200 |
|
5200-09-050 |
Nomad™. 800
Series |
|
5200-10-050 |
GeoCE™, XH™,
XT™, XM™ |
|
5200-11-050 |
Workabout Pro |
|
5200-12-050 |
Carlson Surveyor, Surveyor+ |
|
5200-13-050 |
FC-2500 |
|
Ball-and-Socket Clamp (with a
1-inch ram ball - for 1.25 inch OD Poles) |
 |
|
5200-160 (shown) |
Plain (shown) |
|
5200-161 |
With 40-min vial |
|
5200-162 |
With 20-min vial |
|
5200-163 |
With 8-min vial |
|
5200-164 |
With compass |
|
5200-165 |
With 40-min vial and compass |
|
Open Clamp Pole Brackets |
|
The original SECO Open Clamp Pole Bracket
mounts data collectors and controllers to antenna poles and rover rods
safely and efficiently. Use a a Claw-Quick Release cradle and one of
these popular Open Clamps to create your custom system. Cradles sold
seperately. The aluminum open clamp has stainless steel clamp screws
that attach to the pole and a quick release button. To rotate the data
collector/controller into a position that makes it easy to read, depress the
quick release button to adjustbthe Claw-Quick Release Cradle.
Manufactured from black anodized aluminum. |
|
Number: |
Type: |
 |
|
5198-052 |
Plain |
|
5198-054 |
With 40-min vial |
|
5198-055 |
With Compass |
|
5198-056 |
With compass and 40-min vial |
|
5198-059 |
With 0.15 x 0.92-inch slot |
|
5198-52 |
For 1.5 inch OD Pole |
|
ATV Pole Bracket
System |
|
5198-50 - ATV Bracket System with Radio
Antenna Bar |
5198-51 - ATV Pole Bracket System |
|
This univeral bracket system
is designed to hold a rover rod and a radio antenna pole. It attaches
to the luggage rack with u-bolts and holds all poles 1 to 1.25 inches
diameter. The rigid framework holds up to vibrations and shock from
ATV operation. Quick clamp handles make loading and unloading rover
poles fast and easy but still secure. The fully adjustable unit has
slotted channels so that you can customize all the components of your
system. Comes with storage/transport bag. Weighs 24 lbs. |
 |
The 5198-51 ATV Pole Bracket
System is the same as the 5198-50 system, but does not come with the radio
antenna bar. |
 |
|
Data-Max Data Collector
Holders by Crain |
|
Irreparable damages can be done to a pole
by some metal data collector holders because of repeated or overtightening
of the clamp to the same point of the pole. The patented clamping
system of the Data-Max is designed to grasp the pole or tripod with out
harming it. Elastomeric materials, a large uniform clamping area and a
knob that is designed t o help prevent over tightening. Position your
data collector in one of twenty-six different positions for better viewing.
Make the connection quick and easily |
|
Data-Max Collector Cradles with Dash
Mount |
 |
|
Part# |
Designed for: |
|
91802 |
Topcon FC-100 |
|
91827 (shown) |
TDS Recon |
|
92828 |
TDS Nomad |
|
91842 |
Jett™,
·ce, Explorer, Tracker |
|
91852 |
TDS Ranger 200C |
|
91856 |
TDS Ranger 300X - 500X |
|
91861 |
Trimble TSC2 |
|
91877 |
Allegro |
|
91879 |
Otterbox 1900 |
|
91881 |
Otterbox 2600 |
|
Data-Max Collector Cradles |
 |
|
Part# |
Designed for: |
|
91940 |
Jett™,
·ce, Explorer, Tracker |
|
91950 |
Topcon FC-100 |
|
91960 |
TDS Recon |
|
91962 |
TDS Nomad |
|
91965 |
TDS Ranger 200C |
|
91966 |
TDS Ranger 300x-500x |
|
91970 |
Allegro |
|
91979 |
Otterbox 1900 |
|
91980 |
Otterbox 2600 |
|
Data-Max Collector Cradles with Pole
Mounts |
 |
|
Part# |
Designed for: |
|
91800 |
Topcon FC-100 |
|
91825 |
TDS Recon |
|
91826 |
TDS Nomad |
|
91840 |
Jett™, ·ce, Explorer, Tracker |
|
91850 |
TDS Ranger 200C |
|
91855 |
TDS Ranger 300x-500x |
|
91860 |
Trimble TSC2 |
|
91875 |
Allegro |
|
91878 |
Otterbox 1900 |
|
91880 |
Otterbox 2600 |
|
Data-Max Pole Mount |
 |
|
91900 |
The Data-Max Pole Mount has a modular
design that allows for multiple data collectors and cradles to be used with
the same pole mount. |
|
